Difference between revisions of "HD44780 display"

From Hackerspace ACKspace
Jump to: navigation, search
m (typofix)
m (added location)
Line 175: Line 175:
 
* Alternative display: [[PVG120303]]
 
* Alternative display: [[PVG120303]]
  
[[Category:Parts]]
+
Location: [[Location::Somewhere]] (probably in the left 'soldering cabinet')
[[Category:LCD]]
+
[[Category:Parts]][[Category:LCD]][[Category:Displays]]
[[Category:Displays]]
 

Revision as of 11:41, 12 October 2016

Hitachi HD44780 compatibele LCD

Pinout

A HD44780 compatible display has 14 or 16 pins, depending whether it has backlight. For a working display, you need a minimum of 6 microcontroller ports: RS, EN and D4-D7.

HD44780 pinout
Pin Name Description
1 VSS Ground
2 VDD +5 volts
3 VLC Contrast voltage, normally < 1V
4 RS Register Select (high=Data write, low=Command write)
5 R/W Read/Write (high=read, low=write)
6 EN Enable: high pulse latches command or data
7-10 DB0-DB3 8-bit mode only: data/command bits 0-3
11-14 DB4-DB7 8-bit mode: data/command bits 4-7, or both nibbles in 4-bit mode
15,16 AB,KB (optional) Background light: anode, kathode


Operation

The display can operate in both 8 and 4-bit mode. By default, it will start at 8-bit mode, so you need extra initialization before you can start bit banging per nibble.

For most of the things you do, you need to write either a command (instruction) or just data (text). Therefore, you need a write routine. RS (Pin4) determines the type (command/data), the rest is just nibbles and bytes ;)

Note: for a better timing, refer to table 6 (page 24 and 25) of the datasheet. Also, waiting on the the busy flag is recommended.

8-bit

4-bit mode write sequence
Pin Action Description
EN 0 make sure chip is in normal operation
RS 0 or 1 command->0 or data->1
D0-D7 bits 0 to 7 place byte on bus
EN 1 latch the data onto the chip
wait > 450ns for the data to latch
EN 0 resume normal operation
wait > 5ms for a command to execute, or > 200us for data to set

4-bit

Note that setting the display in 4-bit mode seems to require two commands (three write instructions: the first in 8-bit mode, the other in 2x4-bit: see page 24, 42 and 46 of the datasheet).

4-bit mode write sequence
Pin Action Description
EN 0 make sure chip is in normal operation
RS 0 or 1 command->0 or data->1
D4-D7 bits 4 to 7 place high nibble on bus
EN 1 latch the data onto the chip
wait > 450ns for the data to latch
EN 0 make sure chip resumes normal operation (waiting for the next nibble in 4bit mode)
wait > 5ms for memory to prepare command, or > 200us for data to set
D4-D7 bits 0 to 3 place low nibble on bus
EN 1 latch the data onto the chip
wait > 450ns for the data to latch
EN 0 resume normal operation
wait > 5ms for a command to execute, or > 200us for data to set


physical device

Xopr 23:02, 22 June 2011 (CEST) as of today, there are two HD44780 displays in the space:

  • 2x16 line/char
  • 2x16 line/char for the visually impaired (bigger version)

You can find them in the 'take-off chinese box' in the right most cabinet. Use at will, but be kind to solder a connector to it, so others can take advantage of it too (be nice, share ;).


references

Location: Somewhere (probably in the left 'soldering cabinet')