Difference between revisions of "Polycom"

From Hackerspace ACKspace
Jump to: navigation, search
(added default passcode and the fact that it has an https interface)
(distinctive ring updates (didn't work completely))
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
{{PoE
 +
|Barrel_plug=5.5/2.5
 +
|Barrel_voltage=48V
 +
|802:3af_straight=yes
 +
|802:3af_crosslink=unknown
 +
|Legacy_straight=unknown
 +
|Legacy_crosslink=unknown
 +
|Compatible_straight=unknown
 +
|Compatible_crosslink=unknown
 +
|Unifi_straight=unknown
 +
|Unifi_crosslink=unknown
 +
|Note=
 +
}}
  
 
== VVX 301 ==
 
== VVX 301 ==
 
* Default passcode: <code>456</code>
 
* Default passcode: <code>456</code>
 
* This device can handle 401: unauthorized
 
* This device can handle 401: unauthorized
 +
* has a boot time of about 140 seconds!
 
* webinterface available at https://<ip>
 
* webinterface available at https://<ip>
 +
* has 6P6C (RJ12) AUX port
 +
* has 5 pin (0.1" 3x2 with notch) female header
 +
* has unpopulated internal 2 pin header (J300) seen through the upper slot
 +
* both AUX and header pins 5 are connected (GND?): RJ12 second right, header, first left at the top
  
 
=== factory reset ===
 
=== factory reset ===
 
* power up the phone
 
* power up the phone
−
* Wait for <code>Starting application. press Cancel to interrupt</code> and press Cancel
+
* Wait for <code>Starting application. press Cancel to interrupt</code> and press {{k|Cancel}} (right softbutton)
 
* at the countdown screen, press and hold {{k|1}}+{{k|5}}+{{k|3}} for >3 seconds
 
* at the countdown screen, press and hold {{k|1}}+{{k|5}}+{{k|3}} for >3 seconds
−
* enter the MAC address (without colons) as password (old style sms-mode; note that for entering digits or characters, you need to set the correct input type. Also it's not case sensitive)
+
* enter the MAC address located near the connectors (without colons) as password (old style sms-mode; note that for entering digits or characters, you need to set the correct input type. Also it's not case sensitive.  Button 2 will show you the current mode and next mode)
 +
 
 +
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_VVX_301}}}|connecting_VVX_301|
 +
=== connecting the [[Polycom#VVX_301|Polycom VVX 301]] ===
 +
To get its IP: Press {{k|🏠}}, go down 2 times (Settings ⚙️), Ok (joypad center), {{k|4}},{{k|2}},{{k|1}} (Status, Network, TCP/IP Parameters)
 +
 
 +
Under '''Settings''' &raquo; '''SIP''' &raquo; '''Local Settings''', the following settings are needed (note that a '''Simple Setup''' will get you started as well):
 +
* '''Local SIP Port:''' &lt;make sure this port does not conflict with other SIP devices behind the same NAT&gt;, 0 seems to work as well
 +
* '''Digit Map:''' <code>1[01579]xS0{{!}}1[23]xxS0{{!}}5000S0{{!}}2xxS0{{!}}00x.{{!}}0[1234567]xxxxxxxxS0{{!}}088xxxxxxxS0{{!}}0800xxxx.{{!}}090[069]xxxx.</code>
 +
* '''Server 1''' &raquo; '''Address:''' ackspace.nl
 +
* '''Transport:''' DNSnaptr<sup>1</sup>
 +
* '''Expires (s):''' 110
 +
 
 +
Under '''Lines''' &raquo; '''Line 1''', set the following:
 +
* '''Identification''' &raquo; '''Display Name:''' &lt;anything&gt;
 +
* '''Identification''' &raquo; '''Label:''' &lt;anything for local display&gt;
 +
* '''Identification''' &raquo; '''Address:''' &lt;username&gt;@ackspace.nl
 +
* '''Authentication''' &raquo; '''User ID:''' &lt;username&gt;
 +
* '''Authentication''' &raquo; '''Password:''' &lt;password&gt;
 +
<sup>1)</sup> or use: '''TCPpreferred''' and set '''Outbound Proxy''' &raquo; '''Address''' to sip.ackspace.nl (not tested)
 +
}}</onlyinclude>
 +
 
 +
=== distinctive ring ===
 +
One can use a custom ringtone (using Alert-Info) with the following steps:
 +
* go to '''Preferences''' &raquo; '''Ringtones''' and upload a wav file
 +
** format the file with <code>sox SOURCEFILE.wav -r 16000 -c 1 -b 16 ringtone.wav</code> (or use Audacity/Tenacy, 16khz, 16bit mono wave)
 +
* upload the file
 +
** note that upon reboot the actual file will be lost (remove and re-add the file to restore)
 +
* use the following dialplan: <code>originate {sip_h_Alert-Info=http://illegaleshow.stream/ringtone.wav}user/bergeijk@ackspace.nl YOUR_POLYCOM_EXT xml ackspace</code>
 +
** note that the domain must exist (and not redirect; 404 is fine); the filename must match the uploaded file
  
 
=== TODO ===
 
=== TODO ===

Latest revision as of 16:32, 18 May 2022

Power (over Ethernet) compatibility:
barrel plug: 5.5/2.5 48V

straight crosslink
802.3af yes unknown
legacy unknown unknown
compatible unknown unknown
Unifi unknown unknown

Note:

VVX 301

  • Default passcode: 456
  • This device can handle 401: unauthorized
  • has a boot time of about 140 seconds!
  • webinterface available at https://<ip>
  • has 6P6C (RJ12) AUX port
  • has 5 pin (0.1" 3x2 with notch) female header
  • has unpopulated internal 2 pin header (J300) seen through the upper slot
  • both AUX and header pins 5 are connected (GND?): RJ12 second right, header, first left at the top

factory reset

  • power up the phone
  • Wait for Starting application. press Cancel to interrupt and press Cancel (right softbutton)
  • at the countdown screen, press and hold 1+5+3 for >3 seconds
  • enter the MAC address located near the connectors (without colons) as password (old style sms-mode; note that for entering digits or characters, you need to set the correct input type. Also it's not case sensitive. Button 2 will show you the current mode and next mode)

connecting the Polycom VVX 301

To get its IP: Press 🏠, go down 2 times (Settings ⚙️), Ok (joypad center), 4,2,1 (Status, Network, TCP/IP Parameters)

Under Settings » SIP » Local Settings, the following settings are needed (note that a Simple Setup will get you started as well):

  • Local SIP Port: <make sure this port does not conflict with other SIP devices behind the same NAT>, 0 seems to work as well
  • Digit Map: 1[01579]xS0|1[23]xxS0|5000S0|2xxS0|00x.|0[1234567]xxxxxxxxS0|088xxxxxxxS0|0800xxxx.|090[069]xxxx.
  • Server 1 » Address: ackspace.nl
  • Transport: DNSnaptr1
  • Expires (s): 110

Under Lines » Line 1, set the following:

  • Identification » Display Name: <anything>
  • Identification » Label: <anything for local display>
  • Identification » Address: <username>@ackspace.nl
  • Authentication » User ID: <username>
  • Authentication » Password: <password>

1) or use: TCPpreferred and set Outbound Proxy » Address to sip.ackspace.nl (not tested)

distinctive ring

One can use a custom ringtone (using Alert-Info) with the following steps:

  • go to Preferences » Ringtones and upload a wav file
    • format the file with sox SOURCEFILE.wav -r 16000 -c 1 -b 16 ringtone.wav (or use Audacity/Tenacy, 16khz, 16bit mono wave)
  • upload the file
    • note that upon reboot the actual file will be lost (remove and re-add the file to restore)
  • use the following dialplan: originate {sip_h_Alert-Info=http://illegaleshow.stream/ringtone.wav}user/bergeijk@ackspace.nl YOUR_POLYCOM_EXT xml ackspace
    • note that the domain must exist (and not redirect; 404 is fine); the filename must match the uploaded file

TODO

  • minimum web-setup
  • AUX port pinout
  • deployment server
Retrieved from "https://ackspace.nl/w/index.php?title=Polycom&oldid=9254"