Difference between revisions of "SpaceStateIndicator"

From Hackerspace ACKspace
Jump to: navigation, search
m (Cleaning up featured items)
 
(3 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 +
{{Project
 +
|Featured=No
 +
|State=Active
 +
|Members=Coolepascal
 +
|Description=Arduino Space State indicator for home
 +
}}
 
My verry fancy space state indicator broke down, so i tried to recreate it using stuff i had laying around,
 
My verry fancy space state indicator broke down, so i tried to recreate it using stuff i had laying around,
 
which was a Wemos D1 R1 arduino clown to which i added a shield with a RGB led.
 
which was a Wemos D1 R1 arduino clown to which i added a shield with a RGB led.
Line 47: Line 53:
 
Afther this, you'd select the WeMos board and compile the sketch
 
Afther this, you'd select the WeMos board and compile the sketch
  
<syntaxhighlight lang="cpp">
 
 
<pre>
 
<pre>
 
// Title:      SpaceStateIndicator.ini
 
// Title:      SpaceStateIndicator.ini
Line 247: Line 252:
 
}
 
}
 
</pre>
 
</pre>
</syntaxhighlight>
+
[[Category:Arduino]][[Category:ESP8266]][[Category:LEDs]][[Category:SpaceAPI]]

Latest revision as of 12:29, 22 April 2023

Project: SpaceStateIndicator
Featured: No
State Active
Members Coolepascal
GitHub No GitHub project defined. Add your project here.
Description Arduino Space State indicator for home
Picture
No project picture! Fill in form Picture or Upload a jpeg here

My verry fancy space state indicator broke down, so i tried to recreate it using stuff i had laying around, which was a Wemos D1 R1 arduino clown to which i added a shield with a RGB led. There is also an output to drive a beeper that sounds if the space state changens to 'Open'

Pin Numbering on this board is a bit confusing but this how i did set it up.

Led-Red pin 7
Led-Green pin 6
Led-Blue pin 5

(In this version i did not hookup the beeper anymore, although the software still supports it) The RGB Led is hooked up to the pins using 100 Ohm resistors which offers adequate current to give a clear indication.

In the code provided below the login credentials for your personal wifi router have to be setup. The flashy light sequence "Das blinken das lichtes| shows during startup if everything goes well. The following startup stages are implemented for diagnostics

During startup All colors will flash once
During WiFi login Blue Color flashing Red until login was sucsesfull
Running Red, Green or Yellow depending on the SpaceState or Dark on server error.

Eventualy the Space indicator should show eighter Green for OPEN or Red for closed. If there is a problem in requesting the actual space state, the indicator shows Yellow. And it will remain dark if the server could not be connected.

The SpaceState is requested each 15 seconds, indicated by a show blue flash on the indicator

You can copy the code into a Arduino sketch Select for the board LOLIN(WeMos) D1 R1

If you can't find this board in your Arduino IDE most likely your setup has no support for ESP32 yet. In this case click on File->Preferences And add the following line to 'Additional Boards Manager' https://arduino.esp8266.com/stable/package_esp8266com_index.json

Then tools->Board->Board manager And perform a update. Afther this, you'd select the WeMos board and compile the sketch

// Title:       SpaceStateIndicator.ini
// Function:    Arduino Space State indicator for home
// Author:      CoolePascal (C) 2022 Common Licence dinges

// Board:       WeMos D1 R1
// Port:        ..
// CPU:         ESP-8266 (Warning, Select WeMos Board !)
// Programmer:  Arduino Gemma or WeMos D1

const char *ssid       = "YourWifiRouter";
const char *passwd     = "YourWifiPassword";

const char *host       = "ackspace.nl";
const int   port       = 443;
const char* streamId   = "....................";
const char* privateKey = "....................";

#define ACQUIRE_REPEAT_DELAY 15000
#define ACQUIRE_FLASH_DELAY  100

#define LEDR      D13
#define LEDG      D12
#define LEDB      D7
#define BELL      D8

#define OFF        0
#define LED_RED    1
#define LED_GREEN  2
#define LED_BLUE   4
#define LED_YELLOW 3
#define LED_BELL   8

#define SPACE_ACQUIRE   LED_BLUE
#define SPACE_OPEN      LED_GREEN
#define SPACE_CLOSED    LED_RED
#define SPACE_UNKNOWN   LED_YELLOW

#include <ESP8266WiFi.h>

// Set multi color led
void set_RGB(int rgb)
{
    digitalWrite(LEDR, (rgb&LED_RED)==LED_RED);
    digitalWrite(LEDG, (rgb&LED_GREEN)==LED_GREEN);
    digitalWrite(LEDB, (rgb&LED_BLUE)==LED_BLUE);
    digitalWrite(BELL, (rgb&LED_BELL)==LED_BELL);
}

// Dim the LED, flash once BLUE, then flash RED n times
void Signal(int n)
{
    int t=250;
    set_RGB(OFF);
    delay(t);
    set_RGB(LED_BLUE);
    delay(t);
    for(int i=0;i<n;i++)
    {
       set_RGB(OFF);
       delay(t);
       set_RGB(LED_RED);
       delay(t);
    }
    set_RGB(OFF);
}

// Hardware test
void hw_test()
{
     int t=750;
     set_RGB(LED_RED);
     delay(t);
     set_RGB(LED_GREEN);
     delay(t);
     set_RGB(LED_BLUE);
     delay(t);
     set_RGB(LED_YELLOW);
     delay(t);
     set_RGB(LED_BELL);
     delay(t);
     set_RGB(OFF);
     delay(t);     
}

// Initialize ports and Wifi connection
void setup()
{
    int l=1;
    
    delay(1000);
    pinMode(LEDR, OUTPUT);
    pinMode(LEDG, OUTPUT);
    pinMode(LEDB, OUTPUT);
    pinMode(BELL, OUTPUT);

    hw_test();

    set_RGB(LED_YELLOW);
    WiFi.mode(WIFI_STA);
    WiFi.begin(ssid, passwd);
    while(WiFi.status() != WL_CONNECTED)
    {
        if(l)
           set_RGB(LED_RED);
        else
           set_RGB(LED_BLUE);
        l=l==0;
        delay(300);   
    }
    set_RGB(LED_YELLOW);
}

// Main loop
void loop()
{    
    static int spacestate;
    static int spaceopen=0;
    int chime=0;
    
    WiFiClientSecure client;
    int clientresult=0;

    // Startup, try to connect
    if(client.connect(host, port))
    {
        unsigned long timeout = millis();

        String url = "/spaceAPI/";

        // Connected to server
        set_RGB(SPACE_ACQUIRE | spacestate);
        delay(ACQUIRE_FLASH_DELAY);

        client.print(String("GET ") 
                     + url + " "
                     + "HTTP/1.1\r\n" 
                     + "Host: " + host + "\r\n"
                     + "Connection: close\r\n\r\n");

        while(!clientresult)
        {             
            if(client.available() == 0)
            {
                if(millis() - timeout > 5000)
                {
                    clientresult=-1;
                    // Server connect timeout
                    Signal(8);
                }    
            }
            else
            {
                clientresult=1;
                spacestate=SPACE_UNKNOWN;
            }                 
        }

        // If connected to server
        if(clientresult==1)
        {
            // Read lines from page until done
            while(client.available()>0)
            {
                String line = client.readStringUntil('\n');
                int l = line.indexOf("\"state\":");
                if(l!=-1)
                {
                    if(line.indexOf("\"open\":true")>l)
                    {
                        spacestate = SPACE_OPEN;
                        if(!spaceopen)
                           chime=1;
                        spaceopen = 1;
                    }
                    else if(line.indexOf("\"open\":false")>l)
                    {
                        spacestate = SPACE_CLOSED;
                        spaceopen = 0;
                    } 
                }                
            }
        }    
        client.stop();
    }
    else
    {
       spacestate=OFF;
       BlinkError();
    }
    if(chime)
    {
        set_RGB(spacestate|LED_BELL);
        delay(100); 
    } 
    set_RGB(spacestate);
    delay(ACQUIRE_REPEAT_DELAY);   
}