Difference between revisions of "Polycom"
(added how to connect (and some other details)) |
(distinctive ring updates (didn't work completely)) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 31: | Line 31: | ||
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_VVX_301}}}|connecting_VVX_301| | <onlyinclude>{{#ifeq:{{{transcludesection|connecting_VVX_301}}}|connecting_VVX_301| | ||
=== connecting the [[Polycom#VVX_301|Polycom VVX 301]] === | === connecting the [[Polycom#VVX_301|Polycom VVX 301]] === | ||
| − | To get its IP: Press {{k|🏠}}, go | + | To get its IP: Press {{k|🏠}}, go down 2 times (Settings ⚙️), Ok (joypad center), {{k|4}},{{k|2}},{{k|1}} (Status, Network, TCP/IP Parameters) |
| − | Under '''Settings''' » '''SIP''' » ''' | + | Under '''Settings''' » '''SIP''' » '''Local Settings''', the following settings are needed (note that a '''Simple Setup''' will get you started as well): |
* '''Local SIP Port:''' <make sure this port does not conflict with other SIP devices behind the same NAT>, 0 seems to work as well | * '''Local SIP Port:''' <make sure this port does not conflict with other SIP devices behind the same NAT>, 0 seems to work as well | ||
* '''Digit Map:''' <code>1[01579]xS0{{!}}1[23]xxS0{{!}}5000S0{{!}}2xxS0{{!}}00x.{{!}}0[1234567]xxxxxxxxS0{{!}}088xxxxxxxS0{{!}}0800xxxx.{{!}}090[069]xxxx.</code> | * '''Digit Map:''' <code>1[01579]xS0{{!}}1[23]xxS0{{!}}5000S0{{!}}2xxS0{{!}}00x.{{!}}0[1234567]xxxxxxxxS0{{!}}088xxxxxxxS0{{!}}0800xxxx.{{!}}090[069]xxxx.</code> | ||
| Line 48: | Line 48: | ||
<sup>1)</sup> or use: '''TCPpreferred''' and set '''Outbound Proxy''' » '''Address''' to sip.ackspace.nl (not tested) | <sup>1)</sup> or use: '''TCPpreferred''' and set '''Outbound Proxy''' » '''Address''' to sip.ackspace.nl (not tested) | ||
}}</onlyinclude> | }}</onlyinclude> | ||
| + | |||
| + | === distinctive ring === | ||
| + | One can use a custom ringtone (using Alert-Info) with the following steps: | ||
| + | * go to '''Preferences''' » '''Ringtones''' and upload a wav file | ||
| + | ** format the file with <code>sox SOURCEFILE.wav -r 16000 -c 1 -b 16 ringtone.wav</code> (or use Audacity/Tenacy, 16khz, 16bit mono wave) | ||
| + | * upload the file | ||
| + | ** note that upon reboot the actual file will be lost (remove and re-add the file to restore) | ||
| + | * use the following dialplan: <code>originate {sip_h_Alert-Info=http://illegaleshow.stream/ringtone.wav}user/bergeijk@ackspace.nl YOUR_POLYCOM_EXT xml ackspace</code> | ||
| + | ** note that the domain must exist (and not redirect; 404 is fine); the filename must match the uploaded file | ||
=== TODO === | === TODO === | ||
Latest revision as of 16:32, 18 May 2022
Power (over Ethernet) compatibility:
barrel plug: 5.5/2.5 48V
| straight | crosslink | |
|---|---|---|
| 802.3af | yes | unknown |
| legacy | unknown | unknown |
| compatible | unknown | unknown |
| Unifi | unknown | unknown |
Note:
Contents
VVX 301
- Default passcode:
456 - This device can handle 401: unauthorized
- has a boot time of about 140 seconds!
- webinterface available at https://<ip>
- has 6P6C (RJ12) AUX port
- has 5 pin (0.1" 3x2 with notch) female header
- has unpopulated internal 2 pin header (J300) seen through the upper slot
- both AUX and header pins 5 are connected (GND?): RJ12 second right, header, first left at the top
factory reset
- power up the phone
- Wait for
Starting application. press Cancel to interruptand press Cancel (right softbutton) - at the countdown screen, press and hold 1+5+3 for >3 seconds
- enter the MAC address located near the connectors (without colons) as password (old style sms-mode; note that for entering digits or characters, you need to set the correct input type. Also it's not case sensitive. Button 2 will show you the current mode and next mode)
connecting the Polycom VVX 301
To get its IP: Press 🏠, go down 2 times (Settings ⚙️), Ok (joypad center), 4,2,1 (Status, Network, TCP/IP Parameters)
Under Settings » SIP » Local Settings, the following settings are needed (note that a Simple Setup will get you started as well):
- Local SIP Port: <make sure this port does not conflict with other SIP devices behind the same NAT>, 0 seems to work as well
- Digit Map:
1[01579]xS0|1[23]xxS0|5000S0|2xxS0|00x.|0[1234567]xxxxxxxxS0|088xxxxxxxS0|0800xxxx.|090[069]xxxx. - Server 1 » Address: ackspace.nl
- Transport: DNSnaptr1
- Expires (s): 110
Under Lines » Line 1, set the following:
- Identification » Display Name: <anything>
- Identification » Label: <anything for local display>
- Identification » Address: <username>@ackspace.nl
- Authentication » User ID: <username>
- Authentication » Password: <password>
1) or use: TCPpreferred and set Outbound Proxy » Address to sip.ackspace.nl (not tested)
distinctive ring
One can use a custom ringtone (using Alert-Info) with the following steps:
- go to Preferences » Ringtones and upload a wav file
- format the file with
sox SOURCEFILE.wav -r 16000 -c 1 -b 16 ringtone.wav(or use Audacity/Tenacy, 16khz, 16bit mono wave)
- format the file with
- upload the file
- note that upon reboot the actual file will be lost (remove and re-add the file to restore)
- use the following dialplan:
originate {sip_h_Alert-Info=http://illegaleshow.stream/ringtone.wav}user/bergeijk@ackspace.nl YOUR_POLYCOM_EXT xml ackspace- note that the domain must exist (and not redirect; 404 is fine); the filename must match the uploaded file
TODO
- minimum web-setup
- AUX port pinout
- deployment server
