DMX Arduino

Project: DMX Arduino
Featured:
State	Completed
Members	Roelke
GitHub	No GitHub project defined. Add your project here.
Description	DMX besturing met een arduino
Picture

Een Shield voor de Arduino waarmee je DMX apparatuur kan besturen. Shield is inmiddels geetst.

Schema :

De bijbehorende code :

/* * DMX fade for arduino 008 * based on the code of Tomek Ness and D. Cuartielles * * adapted to arduino 008 by Peter Szakal and Gabor Papp * http://nextlab.hu */ #include "pins_arduino.h" int sig = 11; // signal int value = 0; int valueadd = 3; /* Sends a DMX byte out on a pin. Assumes a 16 MHz clock. * Disables interrupts, which will disrupt the millis() function if used * too frequently. */ void shiftDmxOut(int pin, int theByte) { int port_to_output[] = { NOT_A_PORT, NOT_A_PORT, _SFR_IO_ADDR(PORTB), _SFR_IO_ADDR(PORTC), _SFR_IO_ADDR(PORTD) }; int portNumber = port_to_output[digitalPinToPort(pin)]; int pinMask = digitalPinToBitMask(pin); // the first thing we do is to write te pin to high // it will be the mark between bytes. It may be also // high from before _SFR_BYTE(_SFR_IO8(portNumber)) |= pinMask; delayMicroseconds(10); // disable interrupts, otherwise the timer 0 overflow interrupt that // tracks milliseconds will make us delay longer than we want. cli(); // DMX starts with a start-bit that must always be zero _SFR_BYTE(_SFR_IO8(portNumber)) &amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;= ~pinMask; // we need a delay of 4us (then one bit is transfered) // this seems more stable then using delayMicroseconds asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); for (int i = 0; i < 8; i++) { if (theByte &amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp; 01) { _SFR_BYTE(_SFR_IO8(portNumber)) |= pinMask; } else { _SFR_BYTE(_SFR_IO8(portNumber)) &amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;= ~pinMask; } asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); asm("nop\n nop\n nop\n nop\n nop\n nop\n nop\n nop\n"); theByte >>= 1; } // the last thing we do is to write the pin to high // it will be the mark between bytes. (this break is have to be between 8 us and 1 sec) _SFR_BYTE(_SFR_IO8(portNumber)) |= pinMask; // reenable interrupts. sei(); } void setup() { pinMode(sig, OUTPUT); } void loop() { /***** sending the dmx signal *****/ // sending the break (the break can be between 88us and 1sec) digitalWrite(sig, LOW); delay(10); // sending the start byte shiftDmxOut(sig, 0); for (int count = 1; count < = 512; count++) { shiftDmxOut(sig, value); } /***** sending the dmx signal end *****/ value += valueadd; if ((value == 0) || (value == 255)) { valueadd *= -1; } }