Coinvox 22

Project: Coinvox 22
Featured:
State	Active
Members	xopr
GitHub	No GitHub project defined. Add your project here.
Description	Get an old payphone to work again
Picture
No project picture! Fill in form Picture or Upload a jpeg here

Coinvox 22 looks complete..

..but is stipped empty :(

Keypad I²C interfaced

synopsis

I got myself a Coinvox 22, reasonably cheap. The downside is: the inner workings have been stripped out, so it's just a metal box with keypad and display, a handset with hook-switch and a small transformer.

No coin mech, no ringer, no phone.

inside

handset / hook-switch

The handset is tested and is in good shape. It is connected to a PCB.

• 2 different reed switches
• 4 coils
• 2 3-pin SOT 23 (SMD) diodes(?) (D1, D2: A7 P 45)

J1 Handset connector. Layout is (male) PCB connector side.

|o  spk
|o| mic -
|o| mic +
|o  spk

J2 Connector which ought to go into the main PCB. Layout is (female) connector side.

mic+ 2 |oo| 1 spk
 spk 4 |oo| 3 mic-
 NC1 6 |oo |5 n/c
 NO1 8 |oo| 7 P1
  P2 10|oo| 9 NO2

Note: SW1 switches first (about 2mm) when hanging up, probably used for muting the microphone.

keypad / display

• IC2: PCF8576T (Universal LCD driver for low multiplex rates, I²C address 38h)
• IC3: PCF8574T (Remote 8-bit I/O expander for I²C-bus with interrupt)

  Addresses tied to ground; address 20h.

J Display/keypad connector. Layout is (female) connector side. Int needs pullup, and print is found working at 5V.

SCL 2 |oo| 1 SDA
    4 |oo| 3 
GND 6 |oo |5 VCC
    8 |oo| 7 
Int 10|oo| 9 

Display

• 8 × 14 segment display, characters are filled from the right
• 52 pins with the only the outer 9 connected (36)
• uses 4 back-plane mode (all corners)

Segment layout. Note that bit 3 is not used, which aligns the characters to 16 bit.

       15
    _________ 
 
  | \11 |   / |
 2|  \  |7 /6 |14
  |   \ | /   |
 10----  -----5
  |   / | \   |
 1|  /  |  \4 |13
  | /9  |8  \ |
   __________
        0       o12
 bit 3: not used

Keypad

	col1 (P7)	col2 (P4)	col3 (P5)	col4 (P6)
row1 (P0)	n/c	1	2	3
row2 (P1)	n/c	4	5	6
row3 (P2)	N	7	8	9
row4 (P3)	Vol	*	0	#

To read out the keypad (on interrupt pullup), set one row low and read the column nibble. Repeat for each row. Low bit means key pressed. Theoretically, 1178 key combinations (up to 4 simultaneous keys) can be detected. Key ghosting occurs when pressing keys in the shape of an L (including the 'corner' key), and can be detected if more than one row and more than one column is low when scanning individual lines.

Text on the PCB:

LGCO-CH BTC15 DESKII

4 431 4223 0 22

Text found on some stickers:

Landis & GYR

412197580 A

Version.mec: A

Date fab : 02/95

plans

• upload reference material of the Coinvox phones (hacktic, 't klaphek, telephone museums ([1][2][3][4][5][6][7])
• experiment with my (front fed) coin mech (or look for a top fed mech that fits)
• experiment with a cisco phone (see if I can use the softkeys and the AUX port to read quarters or just Euro coins
• connect an ATA to an old phone

todo

• upload display/keypad initialization commands
• write a library for the display/keypad (fix the hacky code)
• see if the serial protocol of a Cisco phone is of any use
• find an old mechanical phone bell
• identify ICs, obtain datasheet, determine pinouts Success!