Difference between revisions of "Thomson ST2030"

From Hackerspace ACKspace
Jump to: navigation, search
(created first draft on telephone howto)
 
m (added category)
 
(14 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
Partially copied from http://www.voip-info.org/wiki/view/ST2030+Configuration+HowTo
 
−
 
 
[[Image:Thomson ST2030.jpg|thumb|Thomson ST2030]]
 
[[Image:Thomson ST2030.jpg|thumb|Thomson ST2030]]
−
Get the IP address by pressing {k|menu}, {k|config} and select (scroll to) "Information"
+
Some stuff has been taken from the [[Media:ST2030_manual.pdf|old]] and [https://www.voipq.nl/downloads/thomson-ST2030-manual.pdf new] manual, other information comes from [http://www.voip-info.org/wiki/view/ST2030+Configuration+HowTo voip-info.org] [https://www.voip-info.org/wiki/view/ST2030+Tips+and+Tricks twice] and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here].  Apparently, there is support for a distinctive ring (Alert-Info) in firmware  v2.69; this (among other) syntax is supported:
 +
<pre>Alert-Info: <http://www.notused.com>;info=MyMelody9</pre>
 +
Get the IP address by press and hold {{k|menu}} for 3 seconds.
  
 
* go to <nowiki>http://<IP>/main.html or http://<IP>/admin.html</nowiki>
 
* go to <nowiki>http://<IP>/main.html or http://<IP>/admin.html</nowiki>
Line 11: Line 11:
 
Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup"
 
Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup"
  
−
[[Category:Telephony]]
+
Reboot the phone by pressing {{k|directory}} {{k|speaker}} and {{k|redial}} simultaneously for 3 seconds (the outer and center buttons of the 5 buttons which contain transparent keys).
 +
 
 +
Factory reset the phone by unplug power, pressing {{k|headset}} and {{k|mute}} simultaneously, restore power and hold for 3 seconds.
 +
 
 +
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_ST2030}}}|connecting_ST2030|
 +
=== connecting the [[Thomson ST2030]] ===
 +
Under '''SETUP''' &raquo; '''VoIP Service''' &raquo; '''Basic Setup''', the following settings are needed:
 +
* '''Profile Name:''' &lt;anything&gt;
 +
* '''SIP Unregister:''' ''unchecked''
 +
* '''URI Type:''' SIP
 +
* '''SIP Transport:''' UDP
 +
* '''Connect Reuse:''' ''checked''
 +
* '''Service Domain:''' ackspace.nl
 +
* '''Registrar Server Address:''' ackspace.nl
 +
* '''Port:''' 5060
 +
* '''Proxy Server Address:''' ackspace.nl
 +
* '''Port:''' 5060
 +
* '''SIP Local Port:''' &lt;make sure this port does not conflict with other SIP devices behind the same NAT&gt;
 +
* '''TLS Local Port:''' &lt;make sure this port does not conflict with other SIP devices behind the same NAT&gt;
 +
* '''Registration Timer:''' 110
 +
* '''Registration Frequency:''' 110
 +
 
 +
At the bottom, '''User Accounts''', set the following:
 +
* '''Phone number:''' &lt;username&gt;
 +
* '''Phone Name:''' &lt;anything&gt;
 +
* '''Authentication ID:''' &lt;username or number&gt;
 +
* '''Password:''' &lt;password&gt;
 +
 
 +
Under '''ADVANCED''' &raquo; '''Networking''' &raquo; '''Outbound Proxy''', check the following setting:
 +
* '''Outbound Proxy Flag:''' disabled
 +
 
 +
Under '''ADVANCED''' &raquo; '''Voice Settings''' &raquo; '''Codec Setup''', set all codec settings to:
 +
* '''Fixed'''
 +
 
 +
For the dial plan go to '''ADVANCED''' &raquo; '''Voice Settings''' &raquo; '''Advanced''', '''VoIP Dial Plan:''' {{!}}1[01579]x{{!}}1[23]xx{{!}}5000{{!}}2xx{{!}}00x.T{{!}}0[1234567]xxxxxxxx{{!}}088xxxxxxx{{!}}0800xxxx.T{{!}}090[069]xxxx.T{{!}}
 +
}}
 +
 
 +
Note: if you switch profile on the phone (that switches from or to behind-NAT), you have to reboot/powercycle the device for audio to work correctly.
 +
</onlyinclude>
 +
{{PoE
 +
|Barrel_plug=unknown
 +
|Barrel_voltage=9V
 +
|802:3af_straight=yes
 +
|802:3af_crosslink=unknown
 +
|Legacy_straight=unknown
 +
|Legacy_crosslink=unknown
 +
|Compatible_straight=unknown
 +
|Compatible_crosslink=unknown
 +
|Unifi_straight=unknown
 +
|Unifi_crosslink=unknown
 +
|Note=
 +
}}
 +
 
 +
Location: [[Location::hACKspace]] (next to the [[switches|network switch]]), connected to fuse group [[Fuse group::A]].
 +
[[Category:Telephony]][[Category:PoE]]

Latest revision as of 09:57, 14 January 2022

Thomson ST2030

Some stuff has been taken from the old and new manual, other information comes from voip-info.org twice and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here]. Apparently, there is support for a distinctive ring (Alert-Info) in firmware v2.69; this (among other) syntax is supported: 

Alert-Info: <http://www.notused.com>;info=MyMelody9

Get the IP address by press and hold menu for 3 seconds.

  • go to http://<IP>/main.html or http://<IP>/admin.html
  • factory default credentials are "administrator", "784518"
  • go to "SETUP", under section "VoIP SERVICE", click "Basic Setup" (if the link isn't here, you've logged on with the wrong URL)
  • you can now edit the profiles

Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup"

Reboot the phone by pressing directory speaker and redial simultaneously for 3 seconds (the outer and center buttons of the 5 buttons which contain transparent keys).

Factory reset the phone by unplug power, pressing headset and mute simultaneously, restore power and hold for 3 seconds.

connecting the Thomson ST2030

Under SETUP » VoIP Service » Basic Setup, the following settings are needed:

  • Profile Name: <anything>
  • SIP Unregister: unchecked
  • URI Type: SIP
  • SIP Transport: UDP
  • Connect Reuse: checked
  • Service Domain: ackspace.nl
  • Registrar Server Address: ackspace.nl
  • Port: 5060
  • Proxy Server Address: ackspace.nl
  • Port: 5060
  • SIP Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
  • TLS Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
  • Registration Timer: 110
  • Registration Frequency: 110

At the bottom, User Accounts, set the following:

  • Phone number: <username>
  • Phone Name: <anything>
  • Authentication ID: <username or number>
  • Password: <password>

Under ADVANCED » Networking » Outbound Proxy, check the following setting:

  • Outbound Proxy Flag: disabled

Under ADVANCED » Voice Settings » Codec Setup, set all codec settings to:

  • Fixed

For the dial plan go to ADVANCED » Voice Settings » Advanced, VoIP Dial Plan: |1[01579]x|1[23]xx|5000|2xx|00x.T|0[1234567]xxxxxxxx|088xxxxxxx|0800xxxx.T|090[069]xxxx.T|

Note: if you switch profile on the phone (that switches from or to behind-NAT), you have to reboot/powercycle the device for audio to work correctly.


Power (over Ethernet) compatibility:
barrel plug: unknown 9V

straight crosslink
802.3af yes unknown
legacy unknown unknown
compatible unknown unknown
Unifi unknown unknown

Note:

Location: hACKspace (next to the network switch), connected to fuse group A.

Retrieved from "https://ackspace.nl/w/index.php?title=Thomson_ST2030&oldid=9110"