Difference between revisions of "Thomson ST2030"
m (added SRV setting) |
(fixed info, added shortcut keys and PTIME issue fix) |
||
| Line 1: | Line 1: | ||
[[Image:Thomson ST2030.jpg|thumb|Thomson ST2030]] | [[Image:Thomson ST2030.jpg|thumb|Thomson ST2030]] | ||
| − | Some stuff has been taken from the [[Media:ST2030_manual.pdf|old]] and [https://www.voipq.nl/downloads/thomson-ST2030-manual.pdf new] manual, other information comes from [http://www.voip-info.org/wiki/view/ST2030+Configuration+HowTo voip-info.org] and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here]. Apparently, there is support for a distinctive ring (Alert-Info) in firmware v2.69; this (among other) syntax is supported: | + | Some stuff has been taken from the [[Media:ST2030_manual.pdf|old]] and [https://www.voipq.nl/downloads/thomson-ST2030-manual.pdf new] manual, other information comes from [http://www.voip-info.org/wiki/view/ST2030+Configuration+HowTo voip-info.org] [https://www.voip-info.org/wiki/view/ST2030+Tips+and+Tricks twice] and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here]. Apparently, there is support for a distinctive ring (Alert-Info) in firmware v2.69; this (among other) syntax is supported: |
<pre>Alert-Info: <http://www.notused.com>;info=MyMelody9</pre> | <pre>Alert-Info: <http://www.notused.com>;info=MyMelody9</pre> | ||
| − | Get the IP address by | + | Get the IP address by press and hold {{k|menu}} for 3 seconds. |
* go to <nowiki>http://<IP>/main.html or http://<IP>/admin.html</nowiki> | * go to <nowiki>http://<IP>/main.html or http://<IP>/admin.html</nowiki> | ||
| Line 10: | Line 10: | ||
Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup" | Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup" | ||
| + | |||
| + | Reboot the phone by pressing {{k|directory}} {{k|speaker}} and {{k|redial}} simultaneously for 3 seconds (the outer and center buttons of the 5 buttons which contain transparent keys). | ||
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_ST2030}}}|connecting_ST2030| | <onlyinclude>{{#ifeq:{{{transcludesection|connecting_ST2030}}}|connecting_ST2030| | ||
| Line 31: | Line 33: | ||
Under '''ADVANCED''' » '''Networking''' » '''Outbound Proxy''', check the following setting: | Under '''ADVANCED''' » '''Networking''' » '''Outbound Proxy''', check the following setting: | ||
* '''Outbound Proxy Flag:''' disabled | * '''Outbound Proxy Flag:''' disabled | ||
| + | |||
| + | Under '''ADVANCED''' » '''Voice Settings''' » '''Codec Setup''', set all codec settings to: | ||
| + | * '''Fixed''' | ||
For the dial plan go to '''ADVANCED''' » '''Voice Settings''' » '''Advanced''', '''VoIP Dial Plan:''' {{!}}1[01579]x{{!}}1[23]xx{{!}}5000{{!}}2xx{{!}}00x.T{{!}}0[1234567]xxxxxxxx{{!}}088xxxxxxx{{!}}0800xxxx.T{{!}}090[069]xxxx.T{{!}} | For the dial plan go to '''ADVANCED''' » '''Voice Settings''' » '''Advanced''', '''VoIP Dial Plan:''' {{!}}1[01579]x{{!}}1[23]xx{{!}}5000{{!}}2xx{{!}}00x.T{{!}}0[1234567]xxxxxxxx{{!}}088xxxxxxx{{!}}0800xxxx.T{{!}}090[069]xxxx.T{{!}} | ||
Revision as of 18:25, 12 May 2017
Some stuff has been taken from the old and new manual, other information comes from voip-info.org twice and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here]. Apparently, there is support for a distinctive ring (Alert-Info) in firmware v2.69; this (among other) syntax is supported:
Alert-Info: <http://www.notused.com>;info=MyMelody9
Get the IP address by press and hold menu for 3 seconds.
- go to http://<IP>/main.html or http://<IP>/admin.html
- factory default credentials are "administrator", "784518"
- go to "SETUP", under section "VoIP SERVICE", click "Basic Setup" (if the link isn't here, you've logged on with the wrong URL)
- you can now edit the profiles
Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup"
Reboot the phone by pressing directory speaker and redial simultaneously for 3 seconds (the outer and center buttons of the 5 buttons which contain transparent keys).
connecting the Thomson ST2030
Under SETUP » VoIP Service » Basic Setup, the following settings are needed:
- Profile Name: <anything>
- SIP Unregister: unchecked
- URI Type: SIP
- SIP Transport: UDP
- Connect Reuse: checked
- Service Domain: ackspace.nl
- Registrar Server Address: ackspace.nl
- Port: 5060
- Proxy Server Address: ackspace.nl
- Port: 5060
- SIP Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
- TLS Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
- Registration Timer: 110
- Registration Frequency: 110
Under ADVANCED » Networking » Outbound Proxy, check the following setting:
- Outbound Proxy Flag: disabled
Under ADVANCED » Voice Settings » Codec Setup, set all codec settings to:
- Fixed
For the dial plan go to ADVANCED » Voice Settings » Advanced, VoIP Dial Plan: |1[01579]x|1[23]xx|5000|2xx|00x.T|0[1234567]xxxxxxxx|088xxxxxxx|0800xxxx.T|090[069]xxxx.T|
Location: hACKspace (next to the network switch)
