Difference between revisions of "Thomson ST2030"
(added factory reset) |
(Added Stuiterveer's observation) |
||
| Line 46: | Line 46: | ||
For the dial plan go to '''ADVANCED''' » '''Voice Settings''' » '''Advanced''', '''VoIP Dial Plan:''' {{!}}1[01579]x{{!}}1[23]xx{{!}}5000{{!}}2xx{{!}}00x.T{{!}}0[1234567]xxxxxxxx{{!}}088xxxxxxx{{!}}0800xxxx.T{{!}}090[069]xxxx.T{{!}} | For the dial plan go to '''ADVANCED''' » '''Voice Settings''' » '''Advanced''', '''VoIP Dial Plan:''' {{!}}1[01579]x{{!}}1[23]xx{{!}}5000{{!}}2xx{{!}}00x.T{{!}}0[1234567]xxxxxxxx{{!}}088xxxxxxx{{!}}0800xxxx.T{{!}}090[069]xxxx.T{{!}} | ||
| − | }}</onlyinclude> | + | }} |
| + | |||
| + | Note: if you switch profile on the phone (that switches from or to behind-NAT), you have to reboot/powercycle the device for audio to work correctly. | ||
| + | </onlyinclude> | ||
Location: [[Location::hACKspace]] (next to the [[switches|network switch]]), connected to fuse group [[Fuse group::A]]. | Location: [[Location::hACKspace]] (next to the [[switches|network switch]]), connected to fuse group [[Fuse group::A]]. | ||
[[Category:Telephony]] | [[Category:Telephony]] | ||
Revision as of 11:28, 12 December 2021
Some stuff has been taken from the old and new manual, other information comes from voip-info.org twice and http://www.voip-info.org/wiki/view/ST2030+SIP+Firmware+Versions here]. Apparently, there is support for a distinctive ring (Alert-Info) in firmware v2.69; this (among other) syntax is supported:
Alert-Info: <http://www.notused.com>;info=MyMelody9
Get the IP address by press and hold menu for 3 seconds.
- go to http://<IP>/main.html or http://<IP>/admin.html
- factory default credentials are "administrator", "784518"
- go to "SETUP", under section "VoIP SERVICE", click "Basic Setup" (if the link isn't here, you've logged on with the wrong URL)
- you can now edit the profiles
Note: you can disable auto provisioning under "SETUP", section "Auto Provisioning", "Basic Setup"
Reboot the phone by pressing directory speaker and redial simultaneously for 3 seconds (the outer and center buttons of the 5 buttons which contain transparent keys).
Factory reset the phone by unplug power, pressing headset and mute simultaneously, restore power and hold for 3 seconds.
connecting the Thomson ST2030
Under SETUP » VoIP Service » Basic Setup, the following settings are needed:
- Profile Name: <anything>
- SIP Unregister: unchecked
- URI Type: SIP
- SIP Transport: UDP
- Connect Reuse: checked
- Service Domain: ackspace.nl
- Registrar Server Address: ackspace.nl
- Port: 5060
- Proxy Server Address: ackspace.nl
- Port: 5060
- SIP Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
- TLS Local Port: <make sure this port does not conflict with other SIP devices behind the same NAT>
- Registration Timer: 110
- Registration Frequency: 110
At the bottom, User Accounts, set the following:
- Phone number: <username>
- Phone Name: <anything>
- Authentication ID: <username or number>
- Password: <password>
Under ADVANCED » Networking » Outbound Proxy, check the following setting:
- Outbound Proxy Flag: disabled
Under ADVANCED » Voice Settings » Codec Setup, set all codec settings to:
- Fixed
For the dial plan go to ADVANCED » Voice Settings » Advanced, VoIP Dial Plan: |1[01579]x|1[23]xx|5000|2xx|00x.T|0[1234567]xxxxxxxx|088xxxxxxx|0800xxxx.T|090[069]xxxx.T|
Note: if you switch profile on the phone (that switches from or to behind-NAT), you have to reboot/powercycle the device for audio to work correctly.
Location: hACKspace (next to the network switch), connected to fuse group A.
